New sequential turbocharging system by ABB

Fuel and emissions reduction

The new turbocharging system allows maximum fuel savings for two-stroke engines at part and low load, and at the same time maintains the flexibility to go to full engine output immediately. This offers significant long-term economic benefits for vessel operators and charterers with the potential for fuel savings of up to 3% depending on load profile. FiTS2 is the result of ABB’s continued commitment to reduce fuel consumption and emissions. It has been developed in close collaboration with low-speed two-stroke engine designer, Winterthur Gas & Diesel Ltd. (WinGD), which has developed a special tuning for FiTS2.

The new technology enables two-stroke engine builders to offer more flexibility, increasing the potential for higher efficiency and lower operating costs for their customers. NOx emissions from engines fitted with FiTS2 will also remain within IMO Tier II limits. Additional abatement technologies like SCR or EGR can be used to comply with IMO Tier III NOx emissions and will not greatly affect the system while still delivering fuel saving benefits.

Adapting to operator’s needs

Past high fuel prices and low vessel demand led to an increase in ‘slow steaming’ for very large cargo ships, resulting in times in operation outside of original design parameters and therefore causing increased maintenance and repair costs. Typical fuel bills for such vessels have been cited by McKinsey & Co as ‘the largest cost item for shipping lines’ and ‘often exceeding 40% of all costs’ despite current lower oil prices. As the market also continues to see the financial impact of overcapacities, FiTS2 is aimed at addressing the sustained cost vs operational flexibility challenge.  FiTS2 will enable two-stroke engines to operate more efficiently at lower loads, while still enabling rapid return to full engine power without compromise on original design-point efficiencies. As a result, significantly higher savings can be achieved with FiTS2.

Head of Product Line Low-Speed at ABB Turbocharging, Joachim Bremer, said: “From an operator’s or charterer’s perspective, FiTS2 efficiency benefits will enable major cost reductions. Considering for example a typical current fuel bill of 3 – 4 MUSD per year for very large crude oil carriers, FiTS2 has potential to provide fuel cost savings of up to US$100 000 per year, compared with levels typically achievable using conventional turbocharging systems. Big savings are also possible for other vessel types, e.g. for container vessels and can amount to 1 MUSD or more over 10 years. The payback of initial costs can be less than two years, making the FiTS2 solution very attractive”.

Unique design enables cost optimisation

To optimise engine efficiency via improved turbocharging in low and part load, the engine runs in lower loads with only one turbocharger in operation, whereas at higher loads (typically above 50 – 60 % engine load) two turbochargers operate simultaneously. The same principle is applied for very large engines – with FiTS2 they will run with two turbochargers in lower loads and with all three turbochargers for higher load operation. The specially designed cut-off valves for the FiTS2 system are flow-optimised and integrated with the turbocharger casings, ensuring a compact and lean design. Furthermore, the valves can be operated rapidly and automatically under load, without interrupting operation of the engine up to full load. 

 

 

Cut out of one turbocharger for lower engine loads leads to higher scavenging air pressure, increasing the compression ratio and firing pressure optimised by special tuning of FiTS2. The result is enhanced engine efficiency and lower specific fuel consumption while remaining compliant with emission regulations.

 

Robust design and very wide compressor maps of ABB’s A100-L and A200-L turbocharger series allow switching under load without surging and there are no requirements for additional by-pass valves or pipework, making FiTS2 a uniquely simpler and relatively low-cost solution compared to any alternative.

 

Dominik Schneiter, Vice President of Research & Development at WinGD commented: “In our long-lasting strategic cooperation with ABB, WinGD has developed its own engines with features such as optimised two-stroke Miller tuning, high boost pressure ratios, and part load optimised waste gate applications. With the new FiTS2, ship operators can now further benefit considerably from lower auxiliary power consumption, improved response time, and lower fuel consumption of the main engine, improving the CO₂ footprint of their ships at low and mid-load conditions. In today’s changing market conditions such flexibility is a valuable asset to our customers.”

Read the article online at: https://www.drybulkmagazine.com/product-news/22122017/new-sequential-turbocharging-system-by-abb/